Ultra Start 450 SERIES Instruction Manual Page 364
- Page / 490
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
344 Ultra Enterprise 450 Server Owner’s Guide • July 1997
Hot Plug
The system’s disk bays are designed to permit disk drive removal and insertion
while the system is powered on. Hot-plug technology significantly increases the
system’s serviceability and availability, by providing the ability to:
■ Add additional hardware dynamically to enable the system to handle an
increasingly larger workload, perform load balancing, and improve performance
of a running system.
■ Remove/replace faulty hardware with minimal system service disruption.
For more information about hot-pluggable disk drives, see “About Internal Disk
Drives” on page 61.
For More Information
See the documentation supplied with the Solstice DiskSuite software.
- Enterprise 1
- 450 Server 1
- Owner’s Guide 1
- FCCClassANotice 3
- FCCClassBNotice 3
- DeclarationofConformity 5
- Contents 7
- Contents ix 9
- Contents xi 11
- Contents xiii 13
- Preface xv 15
- Using UNIX Commands 16
- Shell Prompts 16
- Conventions 17
- Related Documents 18
- Cautions 18
- Ordering Sun Documents 19
- Sun Welcomes Your Comments 20
- System Overview 21
- Chapter 1 System Overview 3 23
- Locating Front Panel Features 25
- Unlocked Locked 26
- Locating Rear Panel Features 27
- LEDs Keyswitch 28
- Chapter 1 System Overview 9 29
- Name Icon Description 30
- System Setup 31
- Chapter 2 System Setup 15 35
- Chapter 2 System Setup 19 39
- About Setting Up a Console 40
- ■ At 9600 baud 42
- Standby position 49
- Tools Required 62
- Hardware Configuration 63
- Serviceability Features 64
- Status LEDS 65
- Hot-Pluggable Disk Drives 65
- Configurations 65
- ■ Extreme temperatures 66
- ■ Power supply problems 66
- N+1 Power Supply Redundancy 67
- Hot-Swappable Power Supplies 68
- Hardware Watchdog Mechanism 69
- Four Levels of Diagnostics 69
- About Memory 71
- Configuration Rules 72
- Performance 73
- Level Memory Slot Population 73
- CPU Slot 1 75
- CPU Slot 2 75
- CPU Slot 3 75
- CPU Slot 4 75
- DC/DC converters 75
- About DC/DC Converters 76
- About Peripheral Component 78
- Interconnect (PCI) Buses 78
- About Internal Disk Drives 81
- About Power Supplies 84
- About the Serial Ports 87
- About the Parallel Port 88
- About Serial Port Jumpers 91
- Clock mode select jumper 92
- About Flash PROM Jumpers 93
- Target Devices 95
- Bus Length 96
- Cabling and Termination 96
- Multi-initiator Support 97
- Rated Values 99
- Power Supply Output Capacity 100
- Total AC Current Draw 101
- Before You Begin 102
- Step 1. Fill in the quantity 103
- ■ If yes, proceed to Step 7 104
- ■ If yes, proceed to Step 10 104
- Capacity 112
- Limit of the Power Outlet 116
- Parts Installation and Repair 117
- About Handling Boards 120
- Expansion Option 121
- What to Do 122
- C cable between 125
- What Next 130
- Main Logic Board Components 132
- To install a PCI short card 157
- Backplanes 163
- C cable at connector P0500 187
- Backplane 189
- 3. Disconnect the I 195
- C cable at connector P0600 195
- 3. Connect the I 200
- C cable to connector P0600 200
- Storage Devices 203
- Miscellaneous Assemblies 222
- Internal Cables 264
- SCSI Cable 279
- Administration and Networking 343
- Concepts 361
- Disk Concatenation 362
- RAID 1: Disk Mirroring 362
- RAID 0: Disk Striping 363
- Hot Spares 363
- Hot Plug 364
- For More Information 364
- Thermal Conditioning 382
- About Diagnostic Tools 390
- Diagnostics 392
- ■ System console 394
- ■ Front panel Fault LED 394
- OBDiag Menu 395
- OBDiag Commands 396
- Configuration Variables 397
- OBDiag Test Descriptions 399
- FRU : motherboard 405
- About SunVTS Software 407
- About Solstice SyMON Software 412
- Error Indications 413
- Front Panel LEDs 413
- Keyboard LEDs 414
- Power Supply LEDs 416
- Disk LEDs 417
- Error Messages 417
- Software Commands 418
- Solaris prtdiag Command 418
- OBP show-devs Command 418
- OBP printenv Command 419
- Solution 1 424
- Power-on Failures 425
- Video Output Failure 427
- Disk or CD-ROM Drive Failure 427
- SCSI Controller Failures 428
- Power Supply Failure 429
- DIMM Failure 429
- Environmental Failures 431
- Message Type Description 432
- Connector Pinouts 433
- Serial Port Connector Diagram 434
- Serial Port Signals 434
- Parallel Port Signals 436
- SCSI Connector Signals 437
- SCSI Connector Diagram 437
- Pin Signal Pin Signal 438
- Connector 439
- TPE Connector Diagram 440
- TPE Connector Signals 440
- MII Connector Diagram 441
- MII Connector Signals 441
- 13W3 Video Connector Diagram 442
- 13W3 Connector Signals 442
- System Specifications 443
- Physical Specifications 444
- Electrical Specifications 445
- Environmental Requirements 446
- Safety Precautions 447
- Vorschriften 449
- Class 1 Laser Product 450
- Luokan 1 Laserlaite 450
- Klasse 1 Laser Apparat 450
- Laser Klasse 1 450
- Normativas de seguridad 452
- Illustrated Parts Breakdown 455
- Assembly Illustrations 459
- Key Description Part Number 460
- 3 Front Door 540-2832 462
- 1 Main Logic Board 501-2996 464
- 2 Power Supply 300-1302 465
- 5 Keyswitch Cable 530-2314 466
- 1 Left Side Panel 540-2835 468
- 3 Front Door 540-2910 468
- 4 Right Side Panel 540-2836 468
- Glossary 475
- Glossary 457 477
- Index 459 479
- Index 461 481
- Index 463 483
- Index 465 485
- Index 467 487
- OrderingSunDocuments 489
- SunWelcomesYourComments 489
- AIR MAIL 490
- PAR AVION 490
Related products and manuals for Motor vehicle electronics Ultra Start 450 SERIES
(300 pages)© 2020, manymanuals.com. All rights reserved. | 0.347 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals