Ultra Start KE-6 Installation Guide download pdf (Page 8)

Installation Guide

1 Double Pulse Unlock 1 Flash Single .75sec.Lock pulse and double Unlock Pulse

2 3 Second Lock & Unlock 2 Flashes 3 second pulses for Lock & Unlock

*3 0.75 Second Pulses 3 Flashes 0.75 second pulses for Lock and Unlock

Press the Program Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes and 3 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.

1 Ignition Lock Enabled 1 Light Flash Lock when ignition is turned On unlock when off

2 Ignition Lock Only 2 Light Flashes Lock when ignition is On, no unlock when Off.

*3 Ignition Lock Disabled 3 Light Flashes Doors do not Lock or Unlock with Ignition

Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flash and one park light flash)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release the Program. Press the Program momentarily to move to next program step or repeat to change selection.

1 No lock unlock honks 1 Light Flash The horn honks for Panic and Car Finder Mode only.

2 Lock & Unlock honks 2 Flashes Honks for Lock, Unlock, Panic and Car Finder Mode.

*3 All chirps enabled 3 Flashes All horn honks enabled

Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes and 2 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.

Setting 1- Ignition Auto Lock

Setting 2- Horn Honk Settings

Setting 3- Door Lock Options

1 Type 1 1 Flash Unlock before start, lock after start and and shutdown

2 Type 2 2 Flashes Lock pulse after the remote starter shuts off

3* Normal Operation 3 Flashes No additional re-lock pulses

Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flash and one park light flash)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release the Program. Press the Program button momentarily to move to next program step or repeat to change selection.

1Type 1 1 Flash Pulse after start and with lock

2Type 2 2 Flashes Pulse after start only

3*Factory Re-arm 3 Flashes 0.75 second pulse with lock and after shutdown

Press the Program Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes and 3 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release the Switch. Press the Program momentarily to move to next program step or repeat to change selection.

Setting 1- Special Door Lock/ Unlock Operations

Setting 2- Gas/ Diesel Mode- Blue Wire on 14-Pin

Setting 3- Rearm Output- Yellow Wire on 14-Pin connector

1 30 Min Run Time 1 Flash Remote Starter runs for 30min when activated

2 45 Min Run Time 2 Flashes Remote Starter runs for 45min when activated

3*15 Min Run Time 3 Flashes Remote Starter runs for 15 min when activated

Press the Program Switch 4 times to select setting 4 (This will be confirmed by 4 LED flashes and 4 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release the Switch. Press the Program button momentarily to move to next program step or repeat to change selection.

1 10 Seconds 1 Flash 10 sec Max time that starter will stay engaged

2 5 Seconds 2 Flashes 5 sec Max time that starter will stay engaged

3* 3 seconds 3 Flashes 3 sec Max time that starter will stay engaged

Press the Program Switch 5 times to select setting 5 (This will be confirmed by 5 LED flashes and 5 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release the Switch. Press the Program momentarily to move to next program step or repeat to change selection.

1 Auxiliary Output 1 Flashes Output activated by button 5. See page 11 for options.

2 Active Starter Kill 2 Flashes locked, Before ignition and 2 seconds after ignition

Press the Program Switch 6 times to select setting 6 (This will be confirmed by 6 LED flashes and 6 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release the Switch. Press the Program button momentarily to move to next program step or repeat to change selection.

1 Safety ON 1 Flash Must press the start button twice to remote start vehicle

2* Safety OFF 2 Flashes Press the start button once to remote start vehicle.

Press the Program Switch 7 times to select setting 7 (This will be confirmed by 7 LED flashes and 7 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release the Switch. Press the Program button momentarily to move to next program step or repeat to change selection.

Setting 4- Run Time

Setting 5-Maximum Crank Time

Setting 6- Starter Kill/Anti-Grind- Orange wire on 14-Pin connector.

Setting 7- Safety Start Mode

Menu 1 - User Settings

Menu 3 - Starter Settings

1 Short Pulses 1 Flash 125ms pulses with Unlock and on the disarm output.

2* Normal 2 Flashes 750ms pulses with Lock, Unlock and disarm output.

Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)

Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.

Release the Program Button . Press momentarily to move to next program step or repeat to change selection.

Setting 4 - Door Unlock & Disarm Pulse Duration

Note: Programming this option will change the pulse length of this output from

750ms to 125ms.

1 Negative Input/ 30seconds 1 Flash Waits a maximum 30 seconds before starting.

2 Timed Delay/ 15 Seconds 2 Flashes Ignition ON for 15 seconds before remote starting

3* Gas/ Positive Glow Plug 3 Flashes Waits 2 seconds to start if no diesel input is detected

Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes and 2 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release the Switch. Press the Program button momentarily to move to next program step or repeat to change selection.

PROGRAM MODE 2 - ADDITIONAL

1 30 Second Parking Lights on Disarm 1 Flash Park Lights on for 30 seconds on disarm

2 Negative Park Light 2 Flashes Switches the Park Light and the Trunk Release

3* Normal Parking Lights 3 Flashes 2 Park Light Flashes on disarm

Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)

Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.

Release the Program Button . Press momentarily to move to next program step or repeat to change selection.

1 5ms Pulsed Output 1 Flash Short (Quiet) Pulses

2 20ms Pulsed Output 2 Flashes Long (Loud) Pulses

*3 10ms Pulsed Output 3 Flashes Normal (Medium) Pulses

Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)

Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.

Release the Program Button . Press momentarily to move to next program step or repeat to change selection.

Setting 3 Horn Honk Timing

1 Secure Valet Active 1 Flash Ignition “ON” and Program Button is held for 15 seconds

2* Normal Valet Active 2 Flashes Ignition “ON” and Program Button is held for 5 seconds

Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)

Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.

Release the Program Button . Press momentarily to move to next program step or repeat to change selection.

Setting 1 - Secure Valet Mode

Setting 2 - Parking Light Output

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Ultra Start KE-6 Installation Guide Page 8

Comments to this Manuals

Related products and manuals for Motor vehicle electronics Ultra Start KE-6