Ultra Start KE-6 Installation Guide download pdf (Page 4)

Installation Guide

- Control module - 6 button Remote transmitter(s)

- RF Antenna (With Program Switch And LED’s) - 14 pin harness

- 6 pin main harness with dual 30amp power inputs - 4 pin keyless entry harness

- Hood pin safety switch - Install and Owners manual

- Dual 30amp Power Inputs - Dome Light Supervision

- Six button Remote Transmitters - Turbo Timer Mode

- Engine Idle Mode - Remote Panic Feature

- 5 Programable Auxiliary Outputs - Defrost Activation

- Window Roll-Up/Down Output - Dual Car Operation

- Dual Sliding Door Control - Fused Park Light Output

- Programmable Driver’s Door Priority Output - Park Light Diagnostics

- Programmable Dome Light Supervision - (+/-) Glow Plug detection

- Programmable Starter Kill/ Anti-Grind Protection - Programable Wait to Start

- Programmable Passive/Active Starter Kill Output - (+/-) Park Light Outputs

- Dedicated (-) When Running Output - Safety Start Mode.

- Outputs For Pulsed/Latched/Active While Held. - Run Time 15/30 or 45 minutes

- Door Locks .125s/ .75s/3.0s/Double Unlock. - Safety Start Mode

- Auto Tach Learning With Manual Adjustment Option - (-) During Crank Output

- Programmable Horn Output (5, 10 or 20ms output) - Ignition Auto Locks

Recommended Installation Procedures

Components

Feature List

Under Hood Connections - Route the hood pin and tach wires through the firewall

into the engine compartment. Always try to pull the wires through a factory rubber

grommet. If drilling through the firewall, BE CAREFUL. Check for obstructions on both

sides of the firewall. After drilling use a grommet to protect the wires from sharp edges.

Proper Connections - Remote Starters can handle loads of up to 30 amps for

extended periods of time. It is CRITICAL to insure that ALL high current connections are

properly soldered and insulated with quality electrical tape. Failing to insure proper

connections will result in warranty being VOID and can result in a FIRE. The

manufacturer is not responsible for any such damages.

Mounting The Control Module - Never mount the module in the engine

compartment. Select a location under the dash to install the main module. Be certain

that the module is securely attached and does not obstruct any serviceable areas. Do

not force or jam the module into tight places instead of mounting. The module must be

free from all moving parts such as brake and clutch as gas pedals linkages. Do not

place the module directly in front of a heater vent.

Installing the External Long Range Antenna - To insure the best possible

reception, place the antenna in the center of the windshield, behind the rear view mirror.

Before attaching to the glass ensure that the surface is clean and dry. For best results

with range, place the antenna below the tint screen. Run the cable under the head liner

and behind the A-pillar panel. Be careful not to pinch the antenna cable. Plug the

antenna into the BLUE connector on the Control Module.

Yellow Starter 30amp output 12volts during crank only.

Green Accessory 30amp output 12volts in accessory off during start.

Red 12 power 30amp input Constant12volt power

Red 12 power 30amp input Constant 12volt power.

Blue Ignition 1 30amp output 12volts in ignition and start positions.

White Selectable 30amp output Selectable Output. Bottom of page.

6 Pin Power Connector

14 Pin Connector

Green Door Lock Door Lock Output - Programmable.

Red 12 Volt Output Low Current Output For Voltage Inverter.

Blue Door Unlock Door Unlock Output - Programmable.

Pink 2nd Unlock 2nd Unlock Output/ Output - Programmable.

4 Pin Connector Red

2 Pin Connector White

4

5

Yellow (-) Park Lights Negative output for negative park light system.

Black (-) Horn/ Output 5 Negative output for horn activation-

Jumper Selections

Jumper Position One- Second Starter Output On the White Wire.

Jumper Position Two- Second Accessory Output On The White Wire.

Jumper Position Three- Second Ignition* Output On The White Wire.

1 2

3

The jumpers control the output on the white wire from the six pin harness. To change the

output of this wire, place the jumper in one of the following positions

Output on White wire Jumper position

Second Starter Position 1

Second Accessory Position 2

Second Ignition Position 3

Push

Yellow Arm/Output 1 0.75sec Pulse With Lock And On Shutdown.*See P 11.

Orange St. Kill/Output 4 (-) While Locked & Running (Anti-Grind) *See Page 9.

Brown Disarm/Output 2 0.75sec Pulse With Unlock And Before Start.

Red/White Trunk/Output 3 Active When Unlock Button Is Held 3seconds.

Wht/Violet (-) While Running Negative Output While Remote Started.

Green (-) Door Pin Negative Door Trigger Input - 1600m Only!

Green/White Hood Pin Hood Pin Input - MUST BE CONNECTED!!

Purple (+) Door Pin Positive Door Trigger Input - 1600m Only.

Pink Brake Switch Positive Brake Input - MUST BE CONNECTED!!

Black Ground Input System Ground Input - MUST BE CONNECTED!!

Blue/White Tach Input Tach Signal Input - MUST BE CONNECTED!!

Blue Glow Plug (+ or -) Glow Plug Input - DIESEL ENGINE ONLY. ** S

White Park Lights Positive Park light Output - 10 Amp Max.

Black/White Park Brake Park Brake Input - 1600m Only.

Wiring Connectors

Product Description And Installation

Ultra Start KE-6 Installation Guide Page 4

Comments to this Manuals

Ultra Start KE-6 Installation Guide Page 4

Comments to this Manuals

Related products and manuals for Motor vehicle electronics Ultra Start KE-6